Skip to main content

Fence panel sizes: heights, widths and panel counts

WIDTHS
Listed panel widths are 1800mm or 1830mm.
METAL HEIGHTS
Telluria panels are 1680mm or 2000mm high.
PACK QUANTITIES
Rowlinson listings contain 3 matching panels.
CHECKED
Products and prices checked 17 November 2026.

Fence panel sizes vary even when their names say 6ft. Rowlinson lattice and slatted panels are 1800mm wide; the Traditional Lap panel is 1830mm wide. Listed timber heights include 1200mm, 1500mm, 1800mm and 1830mm. Telluria metal panels are 1680mm or 2000mm high. Calculate quantities using the actual width, then allow for posts. England's usual height limits are 1 metre beside vehicle highways and 2 metres elsewhere.

Key takeaways

  • A 6ft label can mean 1800mm or 1830mm wide in this range.
  • Rowlinson timber listings contain 3 panels; Telluria fence panels are sold individually.
  • A 10m run needs up to 6 panels at 1800mm wide, before posts.
  • Fence runs include posts, so panel widths alone do not give the finished length.
  • The Telluria 6H panel is 2000mm high, exactly England's usual 2 metre limit away from vehicle highways.
A tape measure held against a timber fence post beside a fence panel
Check the panel width and your chosen posts before calculating the complete fence run.

Browse fence panels →

Buyer's note from Matt W: I check the millimetre dimensions before comparing panel names. I also check whether the listing contains individual panels or a pack. For an existing fence, I compare the available space with the actual panel width. I would confirm the posts before finalising quantities.

- Matt W, Fencing Stores

What size are fence panels?

The panels in this range are 1800mm or 1830mm wide, with heights that depend on the design.

There is no single exact measurement behind every standard fence panel size. A nominal size describes the product, but the listed millimetres are what you should use for planning.

Width, height and depth describe different parts of the panel. For example, the Grosvenor 6ft x 4ft measures 1800mm wide, 1200mm high and 40mm deep.

Depth matters when you compare panels with the posts you choose. Post sizes vary, so check those details alongside the panel dimensions.

Style also affects your choice. Lap panels use overlapping horizontal boards and are usually the lowest-cost choice. Lattice panels let light through and give climbing plants support.

What heights do fence panels come in?

Listed timber heights include 1200mm, 1500mm, 1800mm and 1830mm; Telluria metal heights are 1680mm and 2000mm.

The familiar 4ft, 5ft and 6ft names are nominal sizes. They do not always match an exact conversion into millimetres.

One foot is 304.8mm. Exactly 4ft is 1219.2mm, 5ft is 1524mm and 6ft is 1828.8mm.

The Grosvenor 4ft panel is listed at 1200mm high, while its 5ft version is 1500mm high. Its 6ft version is 1800mm high.

Use this table to compare actual measurements and listing quantities. Each price shortcode refers to the complete listing quantity shown.

PanelWidth (mm)Height (mm)Panels per listingPrice
Grosvenor 6x4180012003£352
Grosvenor 6x5180015003£384
Grosvenor 6x6180018003£416
Traditional Lap 6x6, Matt's pick183018303£233
Langham 6x6180018003£332
Telluria Fence 5H180016801£294
Telluria Fence 6H180020001£313

The Grosvenor has a curved top with decorative lattice infill. Its 1200mm version suits buyers who want a lower panel with space for light through the lattice.

Grosvenor timber fence panel with a curved top and decorative lattice infill
The Grosvenor 6x4 measures 1800mm wide, 1200mm high and 40mm deep.

Is a 6ft fence panel exactly 6ft wide?

No, the listed 6ft panels are either 1800mm or 1830mm wide.

Exactly 6ft is 1828.8mm. The Traditional Lap panel is listed at 1830mm, while Rowlinson lattice and slatted panels are 1800mm wide.

Those widths are different, despite the shared 6ft description. Check the product dimensions before replacing panels between existing posts.

The same caution applies to height. The Traditional Lap panel is 1830mm high; the Grosvenor and Langham 6ft panels are 1800mm high.

Traditional Lap pressure-treated timber fence panel with overlapping waney-edge boards

Matt's pick: 6' x 6' Traditional Lap Panel Pressure Treated - 3 Panel Pack

Best for: A full-height timber boundary, with each panel 1830mm wide and 1830mm high.

Why we rate it: Traditional overlapping waney-edge boards form the panel. The timber is pressure treated for protection against rot and insect attack.

Price: £233

View Product

How many fence panels do I need?

Divide the fence run by the actual panel width and round up for an initial maximum panel count.

Use matching units for both measurements. For 1800mm panels, divide a run measured in metres by 1.8.

This calculation uses panel widths alone. Posts sit between panels and add to the run, so your chosen posts will often reduce the panel count.

  1. Measure the fence run and subtract any gate width.
  2. Divide the remaining length by the panel width and round up.
  3. Check the layout again with the dimensions of your chosen posts.
  4. For a straight run without a gate, allow one more post than the final panel count.

These worked examples are before posts:

  • 10m with 1800mm panels: 10 / 1.8 = 5.56, so up to 6 panels, or 2 packs.
  • 15m with 1800mm panels: 8.33, so up to 9 panels, or 3 packs.
  • 20m with 1800mm panels: 11.11, so up to 12 panels, or 4 packs.
  • 20m with 1830mm lap panels: 10.93, so up to 11 panels. Four packs contain 12 panels, with one spare.

Rowlinson listings have options for additional matching panels and matching fence posts. Check these before choosing whole packs for your final layout.

The Telluria Door 5H is 870mm wide, so subtract 870mm before counting panels. Compare garden gates before completing the layout.

Telluria Door 5H anthracite grey metal garden gate
The Telluria Door 5H gate measures 870mm wide, 1680mm high and 50mm deep.

How high can a garden fence be without planning permission?

In England, the usual limits are 1 metre beside vehicle highways and 2 metres elsewhere, measured from ground level.

The 1 metre limit also applies beside the footpath of a highway used by vehicles. These limits have exceptions.

The rights do not apply to listed houses or fences within their curtilage. They also exclude boundaries with neighbouring listed buildings.

An article 4 direction or planning condition can remove these rights. In conservation areas, permission may be needed to take down a fence.

If an existing fence already exceeds the limits, its height must not be increased.

The Telluria 6H panel is 2000mm high, exactly 2 metres. A gravel board, raised ground or post cap above the panel needs checking against the ground-level limit.

Watch out: roadside height limits. Next to a road used by vehicles, or its footpath, the limit is 1 metre. Most full-height panels need planning permission there. Check the boundary position before choosing a height.

Which fence panel size should you choose?

Choose the listed width that fits your layout and a height that meets the applicable planning rules.

Compare 1200mm and 1500mm panels for lower boundaries. For taller timber panels, compare the 1800mm designs with the 1830mm Traditional Lap.

The Halkin has a straight top with decorative lattice infill. Its 5ft version is 1800mm wide, 1500mm high and 40mm deep.

Halkin timber fence panel with a straight top and decorative lattice infill
The pressure-treated Halkin 6x5 is supplied as a pack of 3 matching panels.

Langham has horizontal slats with open bar detailing. Slatted panels let some air and light through and have a more contemporary look.

For a surface without routine painting, compare metal fencing. Telluria panels have double-walled galvanised steel and an anthracite grey powder-coated finish.

They are made in Belgium and have a ten-year anti-perforation warranty. Compatible Telluria components are options on the listing.

Standard mainland supplier delivery is included with the Rowlinson packs. Their listings state no warranty term.

"Our range has timber panels with lap, lattice and slatted designs. We also have Telluria steel panels for buyers who want a surface without routine painting."

- Matt W, Fencing Stores

Frequently asked questions

What is the standard fence panel size?

Widths in this range are 1800mm or 1830mm. Check the millimetre dimensions because a 6ft name does not identify one exact width.

Are 4ft fence panels exactly 4ft high?

The listed Grosvenor and Halkin 4ft panels are 1200mm high. Exactly 4ft is 1219.2mm. Use the listed height for your layout.

How many fence panels do I need for 10m?

A 10m run needs up to 6 panels at 1800mm wide, before posts. That is 2 Rowlinson packs of 3. Check post dimensions before finalising the quantity.

Do Rowlinson fence panels come individually?

These Rowlinson listings contain 3 matching panels. Additional matching panels and matching posts are options on the listing.

How high can a fence be beside a road?

England's usual limit is 1 metre beside a highway used by vehicles. The same limit applies beside its footpath. Planning exceptions can also apply.

Does Telluria metal fencing need routine painting?

Telluria's powder-coated surface needs no routine painting. The panels are double-walled galvanised steel. They have a ten-year anti-perforation warranty.

Sources checked